driveshaft specialist page header photo

Home PageContact UsAbout USSite Map

Driveshaft Information

How to measure 
 (if needed) Info on measuring vehicles for a custom driveshaft.  U-Joint Flange- Pinion Yoke measurements.  ID of different Driveshaft Types. 

U-Joint Identification
Basic U-Joint series size guide with dimensions for Inside & Outside lockup

Performer Series Steel Driveshafts
High Performance Steel Driveshafts For Muscle cars, Hot Rods and Race Cars.  Also a Hi-Strength OE replacement driveshaft.

Nitro Series Steel driveshaft
Race Duty Hi-Strength DOM Steel High Performance Driveshaft in 1350 series U-Joint.  2000+Horsepower!

Import Driveshafts
Listings for New and Remanufactured Import Driveshafts for rear drive cars and trucks.

Aluminum Driveshafts

OE  Type Aluminum
Muscle Car - Hot Rods
Import Cars - tRUCKS
HD tRUCK aLUMINUM

 

Truck Driveshafts
Driveshafts for 4x4 and 2 wheel drive.  Front 4x4 Driveshafts. Custom Drive Shafts for lifted trucks. GM, Dodge, Ford, Jeep.

Chevy-GMC Trucks
DODGE TRUCKS
FORD TRUCKS
JEEPS
SPrinter-Mercedes
ALUMINUM TRUCK SHAFTS

Camaro & Firebird Driveshafts
New design 1 pc driveshafts for V-6 Camaro and Firebirds.  Custom Drive Shafts for ALL Camaro's and Firebird's.

Corvette and Cobra
Drive Shafts - Transmission Yokes - Flanges and Parts. 

Classics and Antiques
Carrier bearings for the older Buicks and Cadillac's as well as can rebuild most of the CV driveshafts.  Dodge and Chrysler Ball and Trunion driveshaft conversions.

Driveshaft type Diagrams
Diagrams of most driveshaft types used and measure diagrams for each type.

Driveshaft Part Listings

Transmission Slip Yokes
Transmission Yokes and 4x4 Transfer Case Slip yokes for cars and trucks.

IMPORT TRANSMISSION YOKES 

Transfer Case Bolt-on Yokes
Bolt on fixed type end yokes for transfer case.  CV type and single U-Joint yokes.  See Transmission for Slip type yokes

Pinion Yokes - Differential
Differential pinion yokes and flanges.

Driveshaft Component Parts
Listings for Universal Joints, Carrier Bearings, U-Bolts-Bolt/Strap Kits, Mid-Slip Yokes, Splined Stub Shafts. CV parts and diagrams.

Driveshaft Questions
Common Driveshaft questions and answers.

Customer Comments
Email feed back and testimonials from our customers.

Shop Photos

M2  Measure Sheets for 2 Piece Driveshafts

How to Measure for Driveshafts that have a Center Support Bearing (carrier bearing) near the middle of the driveshaft.  All 2 piece driveshaft are Hi-Speed Balanced as one rotating assembly.

 If you have any questions - Please call.  We are here to help in any way possible.

m2-1 measure diagramM2-1
2pc Shaft using our New Trans Yoke and has a Regular Pinion Yoke.

This is the most common set up on trucks thru the year 2000, then Ford and Dodge went to flat type flanges.  This is also used on some early GM cars

<<Click Image to View or here for Quote/Order >>M2-1 QUOTE - ORDER FORM.pdf

 

 M2-2 measure diagram
M2-2
2pc Shaft using YOUR Trans yoke and has a Regular Pinion Yoke

Same as the M1-1 but using a slip yoke you are sending us.  We need the trans yoke to install on the driveshaft and Hi-Speed Balance the complete assembly.

<<Click Image to View or here for Quote/Order >> M2-2 QUOTE - ORDER FORM.pdf

 

 M2-3 measure diagram for driveshaft
M2-3
2 piece Shaft using a new Trans Slip yoke and Flat Type Flange at Differential

This is used on late Ford and Dodge trucks.  It is also found on some early GM cars with a Constant Velocity at the differential.

<<Click Image to View or here for Quote/Order >>  M2-3 QUOTE - ORDER FORM.pdf

 

 
 M2-4 measure diagram for 2 pc shaftsM2-4
2 Piece Shaft using YOUR Trans Yoke and Flat Flange at Differential

Same as M2-3 but using a Trans yoke you are sending us.

<<Click Image to View or here for Quote/Order >>M2-4 QUOTE - ORDER FORM.pdf

 

 

 M2-5 2pc driveshaft measure diagram
M2-5
2 Piece shaft with Bolt on (fixed)Trans Yoke and Regular Pinion Yoke

This diagram is mostly for Trucks that have a fixed or bolted on Trans yoke and a regular type Pinion Yoke

<<Click Image to View or here to order >> M2-5 QUOTE - ORDER FORM.pdf


 
 M2-6 2 piece shaft with 2 flangesM2-6
Flat type Trans Flange and Flat type Pinion Flange

This is used mostly in Truck applications as well as some import products like BMW

<<Click Image to View or here for Quote/Order >> M2-6 QUOTE - ORDER FORM.pdf

 

 

 
 M2-7 2 piece measure sheet for driveshaftsM2-7
Flat type Trans. Flange and Regular type Pinion Yoke

This type has a flat style flange at the Transmission or Transfer Case and a regular type Pinion Yoke.

<<Click Image to View or here for Quote/Order >> M2-7 QUOTE - ORDER FORM.pdf

 

 
 M2-8 how to measure for driveshaftM2-8
GM X-Type Frame found on early GM Vehicles

Use this for late 50's and Early 60's GM Cars.  It is also used with mid to late 60's and early 70's GM Trucks with the "Truck Arm" suspension where the center support bearing fits in a frame tunnel.  Note: On the short bed trucks we can go to a 1 pc shaft but not the long bed.

<<Click Image to View or here for Quote/Order >> M2-8 QUOTE - ORDER FORM.pdf